pro lathe duplicator

PRO LATHE DUPLICATOR

YOU CAN TURN

Balusters Newel Posts Bed Legs Table Legs Chair Components

Porch Posts & Spindles Baseball Bats Rosettes Drum Sticks

Walking Sticks Lamps Candle Sticks Fishing Lures & many others

Vega Duplicators produce a wide range of turnings quickly, easily and accurately, on your lathe, with minimal turning experience. They are designed and constructed to withstand production turning environments. Thoughtfully designed accessories provide even greater versatility for turning difficult, unusual or custom parts. The Vega Professional Duplicator fits all full sized Lathes and is available with standard travels of 16", 36", 96" and 120". For specific application information and technical support, your dealer and a helpful and knowledgeable factory staff is just a phone call away.

~WHAT WILL THE DUPLICATOR DO?

For all but the most experienced hand turners, the Vega Pro duplicator will give you much faster stock removal, good surface finish on most woods and the ability to produce duplicate spindles that are exactly the same. The duplicator will give you superb tool control, making turning safer, faster and more accurate.

~HOW DOES IT WORK?

The duplicator works on the same principle as a key cutter. You either make a template (which has the profile of the turning cut into it) or mount an original turning that you wish to copy (4" diameter maximum for original turnings). Excess material is quickly removed by locking cutters in-out motion and turning the handwheel of the duplicator to move the cutter along the axis of the lathe bed. Then the last cuts are made, working from the high points of the turning down into the coves..

~CAN I STILL USE CHISELS?

Yes. The first option is to remove the duplicator by loosening 2 bolts. The second option is to mount the duplicator on the back side of the lathe and turn the cutter upside down. This gives you access to the front of the lathe for hand turning. The third option is available only to those with a reversing lathe. This option is to mount the duplicator on the front and hand turn from the back side of the lathe with the spindle reversed. Note that some lathes may be constructed in such a way as to prevent mounting the Vega Duplicator on the rear of the machine.

~HOW DEEP A CUT CAN I TAKE?

It can reduce the diameter by up to 3/4" per pass. To obtain this deep a cut, a stout workpiece that will not deflect under load is necessary and a lathe with adequate horsepower (3/4 hp Minimum).

~GREAT FEATURES

RIGIDITY - Results in the cutter being held firmly in place to achieve a smooth cut.

DURABILITY - Heavy construction and low friction material result in a very durable tool. all wear points have mechanical take-ups.

EASE OF OPERATION - All controls are located for fast and convenient access.

ACCESSORIES


~Slender Turning Accessory 1.875 A traveling steady rest which solves the problem of spindles “whipping.” (Because they are structurally weak due to their length to diameter ratio.) This device bolts to the front of the Duplicator carriage and supports the spindle inside a large bearing with 4 opposing ľ” diameter set screws (Handles up to 1 7/8” square stock).
~Slender Turning Accessory 1.375 Functionally similar to the Slender turning 1.875 unit, but will only hold up to 1 3/8” square spindle blanks. This unit is designed mainly for simple tapers which can be cut in one pass. Typical turning for this unit would be Windsor chair spindles, drum sticks, pool cues, etc.
~Spiral Attachment Turn the Spindle using the duplicator cutter and then mount a router on the duplicator. The Spiral Attachment will rotate the spindle while cutting the flutes or reeds. Has a built in 24 tooth index plate.
~Router Bracket Lets you mount a round motor router to the tool holder spindle of the duplicator. Use your lathes indexer to position the turning for fluting. New design allows vertical or tipped back positioning of the router to accommodate larger diameter turnings.
~Diamond Vee Cutter This is a high performance cutting system utilizing double ended Carbide inserts. Advantages include superior surface finish on turnings, long cutter life, no sharpening, indexable for fast & accurate tool changes. Great for most types of wood.
~Special Cutters The Square Shoulder Cutter is a carbide insert cutter for cutting clean 90 degree left or right facing shoulders. It uses the Diamond Vee style insert to cut furniture knobs and round type shapes. Both are indexable tools.
~Steady Rest This steady rest bolts to the lathe bed. It has 2 arms with soft rollers and bearings. The soft material helps prevent the wood from compressing while spinning. This keeps the steady rest running smooth and quiet. This design is very good for small batches of parts or occasional long spindles.
~Template Maker This tool lets you quickly and easily draw profile onto template material form an original turning. Simply put the master turning in the lathe and follow the profile using the template maker following tool. A pencil then traces the profile onto the template material. Cut your template and make your turnings.