~Edge Belt Sander~  

Model EBS-6              6" x 132" Belt               Industrial Duty

Extremely Heavy Duty!!  A solidly built Machine designed to withstand the rigors of day to day production sanding.  compare this Machine to ANY on the Market...  We are sure you will make a clear cut choice - The VEGA EBS-6   controls and easy adjustments, making duplication of turnings fast, easy and fun.  All Vega Edge Belt Sanders include thoughtfully designed features which allow greater productivity and durability at a truly realistic price.

~BELT TENSION ASSEMBLY

A superior idler pulley mechanism makes belt tracking insensitive to belt tension changes.  The 5" Urethane coated steel pulley with heavy sealed bearings provides excellent belt support.

~TABLE SUPPORT BRACKET

The main table support brackets allow the table to be tilted up 15 degrees and down 48 degrees by loosening the very secure tee handle.  Table also adjusts in and out.  Table can be adjusted vertically to provide 4" bias.  No wrenches required.  Table adjusts in and out to provide desired clearance from the belt.  Table size is 12" x 48".

~ ADJUSTABLE CURVE PLATTEN

(Accessory) It is always a challenge to sand large curves without producing a series of arcs.  This accessory solves the problem for a wide range of shapes.  The large adjusting knob varies the arc of a curve from flat to about a 12" radius.  Quickly attaches to the rear of the sander and can be used with Accessory Side Table.

~ OSCILLATING DRIVE

(Accessory) A 1/20 HP 110 volt Gearhead Motor oscillates the idler pulley to provide 1" belt movement 32 cycles per minute.  An electrical disconnect is provided should you want to use it in a non-oscillating mode.  Very easy to install on standard unit.

~SPECIFICATIONS

Models Available
#71103  Model EBS 6-1 110v 1ph. 2hp.
#71104  Model EBS 6-2 220v 1ph. 2hp
#71105  Model EBS 6-3 220v 3ph. 3hp
Above models include 1 side table with
support brackets, mitre gage, two (2)
adjustable dust pick-ups, and one 8" x
48" platten.
Accessories for Above:
#71080 End Table Assembly
   ~ Fully adjustable for height and tilt.  Operates with 5" diameter idler pulley for sanding inside radius's.  
#71066 Second Side Table
   ~ Same as standard Front Table.  Can be used with the Adjustable Curve  Platten or the Rear Flat Platten.
#71102 Adjustable Curve Platten
   ~ For sanding large radius inside curves. (see description above.)
#71013  Oscillating Drive
   ~ 'Bolts on' to provide 1" belt excursion for longer belt life and more efficient stock removal. (see description).
#71166 Rear Flat Platten 8" x 48"
   ~ 'Bolts on' to provide a second flat sanding station.  Constructed of Hard Maple covered with graphite 
      impregnated canvas.
Features:
Ideal belt speed - 4000 FPM Easy belt changes
Warranty - 1 year Adjustments are top located for easy access
Pedestal design for operator foot room and easy to clean-up.   Tee handles on nearly all adjustments - wrenches not required.
Table - Formica faced & reinforced 1 1/8 MFD Tilts 15 degrees up and 48 degrees down.  4" bias adjustment. Motor - American Made 1825 RPM, TEFC.  11/8 shaft, industrial type.
Dust Pickup - Adjustable Hoods (2) Platten - Surface Ground Steel 8" x  48" with graphite coated canvas wear plate.
Drive Pulley - 8" diameter steel. Idler Pulley - 5" Urethane coated steel.
Miter gage 18" Toggle tension release for fast easy belt change.
Superior idler pulley mechanism makes belt tracking insensitive to belt tension changes. Weight 475 lbs.